Waste Management Program

fact sheet

Division of Environmental Quality

Director: Kyra Moore

This document was prepared by the Missouri Department of Natural Resources’ Solid Waste Management Program (SWMP) to provide guidance for the proper design and construction of gas monitoring wells to comply with the quarterly monitoring required by 10 CSR 80-3.010(14) and 10 CSR 80-4.010(14).

For any active demolition or sanitary landfill, ground monitoring for gas migration must be performed using gas monitoring wells.

Well Design

Proper design and construction of gas monitoring wells is critical in obtaining true soil gas concentrations. All wells should be designed to minimize air intrusion into the system so accurate soil gas samples can be collected. All monitoring wells deeper than 10 feet are regulated by the department’s Missouri Geological Survey (MGS)  formerly known as the Division of Geology and Land Survey (DGLS) and must be installed by a certified well driller. For further information on this subject, call 573-368-2165.

SWMP recommends the following well designs:

  • Permanent Monitoring Well - Please refer to Missouri Well Construction Rules 10 CSR 23-4. Refer to figure 1, which illustrates major components.
  • Push Probe/Direct Push Well - This design does not meet the current codes but a variance to install this type of well can be obtained through MGS. Refer to figure 2, which illustrates major components.
  • Spike Probe - This is not actually a monitoring well by definition since its use is confined to a depth less than 10 feet below ground surface. For this reason no variance is required from MGS. Refer to figure 3, which illustrates major components.

Spike probes may be used where shallow groundwater, approximately 10 feet or less below the surface, prevents construction of a drilled well. However, this circumstance should be rare. The SWMP does not consider bar punch testing for shallow soil migration to be an effective monitoring method for other than instantaneous monitoring to evaluate the extent of shallow lateral gas migration.

Monitoring wells should be designed to monitor all unsaturated soil and rock down to an elevation equal to the bottom elevation of the landfill. Wells can be designed with a single riser screened from just below the well seal to the bottom of the landfill. They can also consist of a well cluster with multiple risers screened across different geologic units, as long as monitoring is provided for every geologic unit between the ground surface and an elevation equal to the bottom of waste in the landfill. Well clusters are valuable for isolating separate distinct permeable zones that would be likely to transmit gas (sand seams, fracture zones, karst features, mine shafts, etc.) interval.

Gas monitoring wells must also be designed to prevent intrusion of atmospheric air into the wells at all times; the cap should have a valved or quick-connect sampling port for the direct attachment of the gas sampling instrument, so that samples may be drawn directly from the well.

Well Locations

The location of gas monitoring wells must be approved by the SWMP, and should be based on a characterization of geologic and hydrologic conditions at the landfill site and on the adjacent land uses.

Subsurface monitoring for methane must be conducted around the perimeter of the disposal area. The solid waste regulations state the point of compliance for regulatory limits of methane migration is at the landfill property boundary. However, at some sites where the edge of the fill area is far from the property boundary, landfill owners/operators have chosen to locate gas monitoring wells closer to the waste mass to provide early detection so action can be taken to prevent gas migration from the landfill property.  In these situations, the gas monitoring wells are considered to be points of compliance. Landfill owners/operators will be required to take the actions specified by the SWMP’s Methane Gas Policy dated June 2012 if methane is detected above regulatory limits in the original monitoring wells. The monitoring wells may be relocated to the property boundary as part of the gas migration investigation, with prior approval of the SWMP. If the newly installed wells are in compliance, the owner/operator will not be required to carry out formal corrective actions.  The owner/operator should keep this in mind when choosing gas monitoring well locations.

Monitoring wells should be located in areas where gas migration is most likely to occur or to become a threat to the public or the environment. The wells should be located in critical areas such as between the landfill and adjacent buildings and sand or gravel bedded utility lines.

Monitoring locations should be spaced no more than 500 feet apart, with closer spacing depending on the permeability of the ground (the more permeable, the closer the spacing) and on the number of nearby features that could be potentially affected. Gas monitoring wells closer to the waste mass should not be placed directly opposite gas extraction wells on the fill area; monitoring wells may give a falsely low reading if they are in the zone of influence of the extraction well.

Monitoring may not be necessary in areas where the potential for gas migration is low. For example, a stream or a valley may form a natural (hydrologic or topographic) cutoff to prevent the flow of gas through the ground.  However, in these situations, the owner/operator must make a formal written demonstration that a natural cutoff exists, and that demonstration must be approved by the SWMP.


All wells should be designed to minimize air intrusion into the system, which can dilute the sample, making it unrepresentative. Selection of well designs and locations should be based upon what zones are to be monitored. A monitoring well certification record shall be used to report new monitoring well construction. Monitoring well certification record forms and monitoring well construction can be obtained online


Farquhar, Grahame, Monitoring and Controlling Methane Gas Migration, course notes presented at April 1993 Sanitary Landfill Design and Management training, offered by the University of Wisconsin, Madison, College of Engineering.
Missouri Department of Natural Resources, Flood Grant Team, An Analysis of Landfill Gas Monitoring Well Design and Construction.
Technical Bulletin - Figure 1 and Figure 2
Technical Bulletin - Figure 3


Nothing in this document may be used to implement any enforcement action or levy any penalty unless promulgated by rule under chapter 536 or authorized by statute.

Nothing in this document may be used to implement any enforcement action or levy any penalty unless promulgated by rule under chapter 536 or authorized by statute.

For more information